WARNING: This product can expose you to chemicals that are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.Flashed directly through the (OBDII) Diagnostic port of your vehicle (10-15 minutes).
With over 10 years of experience in Bosch and Siemens engine management calibration, Unitronic is able to utilized its industry leading tools and equipment to assure an optimal calibration; delivering maximum performance, while maintaining complete OEM-like reliability and drivability.
Development begins using its in-house engine dyno housed in an environmentally controlled cell; closely monitoring a plethora of operational data, utilizing industry leading calibration tools and resources. Additional validation and results comparison are completed using its in-house Maha Chassis dyno as a second step of product development. Beta calibrations are then tested in race and street scenarios, using multiple cars throughout the world under various driving conditions. This engine calibration strategy ensures Unitronic Performance Software delivers maximum performance, OEM-like drivability and reliability anywhere in the world. Unitronic Performance Software is only released to its Clients once development is thoroughly completed in accordance to UnitronicÂ’s strict standards.
OEM “fail safes” are retained within the ECU calibration. Close monitoring of all operation parameters ensures that engine operation stays within factory components limits, resulting in an OEM-like drivability and reliability.
Engine speed limit protection active under warm-up to prevent potential damage when coolant temperature is not within operation range.
Professionally calibrated to improve engine response and reduce drive-by-wire lag. Optimized torque curve for more low end torque and faster turbo spool.
Due to the large flat torque curve, the calibration offers a smooth operation under normal and hard acceleration. This results in linear acceleration with constant torque without low end torque peak that will cause loss of traction and uncontrollable power surge, at the expense of high engine speed power.
Unitronic development team delivers the maximum power output while staying within the operational limits of the factory components used. Specifically, this results in the highest engine performance without sacrificing the reliability of the engine, turbocharger, or other engine components.
Aligned with the OEM strategy, the calibration is designed to offer a large flat torque plateau to provide a smooth and linear power band. Maximum torque output is achieved sooner and maintained longer which creates a broader torque plateau and greater area under the curve. This results in an improved acceleration and optimal engine operation.
Optimized timing and injection under cruising condition for an improved fuel efficiency.
Vehicle speed limiter within ECU is removed. (If automatic, subject to transmission rotational speed limit)
Engine calibration optimized to take advantage of higher fuel quality to extract maximum energy from the combustion. Therefore, when using a higher octane fuel, more power and better fuel efficiency will be achieved.
With maximum turbocharger efficiency reached with Stage 1, Stage 1+ and Stage 2, Unitronic developed a unique solution to bridge the gap between Stage 2 and Stage 2+ (IS38) turbo upgrade. This results in the use of a factory IHI IS20 turbocharger, from a MK7 GTI, as a complete bolt-on solution producing a power increase of 44hp and 19lb-ft tq over the Stage 2 output, using the OEM turbocharger (IS12).
Full Staged Software Suite
Includes all Stage 2 tune variants and all lower software stages as well.
Required Hardware
3 Inch Downpipe for 1.8/2.0 TSI Gen3 MQB (AWD) by Unitronic3'' Downpipe for 1.8 TSI Gen3 MQB (FWD) by Unitronic
Carbon Fiber Intake For MK7 GTI | MK7 R | 8V A3 | 8V S3 | MK3 TT
Intercooler Upgrade Kit for 1.8/2.0 TSI Gen3 MQB by Unitronic
Unitronic Turbo Inlet Elbow For 1.8/2.0 TSI Gen3 MQB
*Unitronic cannot guarantee results for Clients using third-party hardware and results may vary as a result. Post-sale technical support can not be provided by Unitronic or its affiliates for Clients using third-party hardware.
Recommended Hardware
Carbon Fiber Intake System With Air Duct For 1.8/2.0 TSI Gen3 MQBCharge Pipe Upgrade Kit for 1.8/2.0 TSI MQB
Intercooler Upgrade Kit for 1.8/2.0 TSI Gen3 MQB by Unitronic
Electrical/Electronic parts are non-returnable.
- PDP tag:
- Free Shipping*
