WARNING: This product can expose you to chemicals that are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.Choose Between The Following SKU's Above: JHM-27TLWFWCC-forged-S1OrgOrg, JHM-27TLWFWCC-forged-S3CerMet.
JHM V6 CHROME-MOLY FORGED SINGLE-MASS LIGHTWEIGHT FLYWHEELS AVAILABLE NOW!!
NOTE: This is now an option you can choose instead of our traditional Alumimum Flywheels.
The Chrome-Molly Forging allows fewer opportunities for failure and promotes uniform, efficient heat transfer from the clutch disc. This is to prevent warped friction inserts or loose ring gears. It is strategically lightened, stronger, safer and has better thermal capacity than OE cast flywheels. With smooth operation at all RPMs, these flywheels meet the needs of both the enthusiast and the hardcore racer.
Features:
• Chatter Free
• Easier engagement from a stop compared to aluminum
• Improved Engagement and momentum when Launching
• One-piece Chromium Molybdenum forging is stronger and more durable than billet steel, aluminum or cast iron.
• Tough, precision-made and dynamically balance
• Lighter and stronger than stock flywheels
• Integral ring gear is induction-hardened for maximum gear life
• Material is properly distributed for strength, greatest heat dissipation and reduced inertia
• CAD-designed, CNC-machined and computer balanced for quality and precision
• Improved throttle response and acceleration
• Smooth operation at all RPM’s
• Optimal mass distribution
• Lead-in chamfers
• Heat treated and tempered
• SFI Spec. 1.1 Certified Design
Flywheel Weight:
OEM: 28lbs
JHM: 14.5lbs
JHM Flywheel is 13.5lbs Lighter!
Included:
1x JHM Chrome-Moly Forged Lightweight Flywheel
1x OEM Pilot Bearing (Pressed Into Flywheel)
8x OEM Flywheel Bolts
NOTE: Flywheel to Crankshaft bolts must be torqued to 65 ft lbs with the use of loctite on the threads
JHM has been testing and abusing the B7 RS4 pressure plate since early 2009. This started with our B6-B7 S4 and B7 RS4 product development. In mid 2009, we purchased a 2005 B6 S4 to compliment our long time R&D car, our flagship 2001.5 Nogaro Blue B5 S4. To this day we still own, daily drive, and test products on our in house B5 S4. Of course this car has the full JHM treatment which now features a JHM built motor with Record Setting JHM RS6-R turbos. This car has been running our new Lightweight Flywheel and Clutch setup (Stage 4) with the B7-RS4 pressure plate for quite some time. We have seen much better results with this new kit than we had with the older B5 RS4 pressure plate setups we used to sell.
In true JHM style here are some videos of some of the abuse we have put this clutch setup through during our R&D process:
NEW VIDEO AS OF December 2012. 10.8 quarter mile pass with our 2001.5 B5 S4, full weight street car with stock hood and full exhaust. This car has the stage 4 clutch can hold some power.
JHM burnouts and abuse from late 2010 with our B7 RS4 (we have since gone faster all motor). VIDEO -->HERE>
JHM Record Setting Track Run: 11.96 @ 116mph with our Stage 1 B6 S4 Vortech Supercharger Kit on a stock motor. VIDEO -->HERE>
Yes, these are videos of our in house 2005 B6 S4 and our B7 RS4, not a 2.7t. These videos better demonstrate the performance of this new clutch kit due to the fact that these cars have way more instant torque than the B5 S4 because of their increased displacement (2 more cylinders), all motor horsepower design, and no turbo lag. Pressure plate manufacturers use torque - not horsepower - to measure how much power a clutch kit can hold. Torque - not horsepower - is a measurable value. Horsepower is created through torque and revolutions per minute of the motor using a mathematical calculation, not by measuring the force of the motor directly. Therefore torque - not horsepower - is critical when measuring the performance of a clutch and pressure plate.
We looked at these results from our V8 cars and thought that we had to get this setup on our B5 S4. We wanted to offer our in-house B5 S4 (and eventually our customers) the extra durability, street-ability, and lower cost of the B7 RS4 pressure plate. Unfortunately, the B7 RS4 pressure plate IS NOT a bolt on part for the B5 S4. With our custom made lightweight flywheel, now it is.
This flywheel is not like others out there. It's not just a cheaply made, mass produced, modified flywheel but a high quality part, made here in California. It's designed specifically to accept the B7-RS4 pressure plate. Have we mentioned that with our proprietary LWFW design, the B7-RS4 pressure plate offers an increased clamp load over previous setups? (We had it independently tested and we found that it has 18% more clamp load than the B5 RS4 pressure plate). It also gives you a lighter and more precise pedal feel leading to all around better drivability in a B5 chassis car.
We have already gone 11.1 @ 130mph back in 2007 with a stage 3 S4 using a B5 RS4 pressure plate along with a Stage 3 style clutch disc. We know this new kit is much better than our previous offerings that we had on the car. This pressure plate and flywheel setup has 18% more clamp load!!! That allows it to hold more torque than the old style, B5 RS4 pressure plate setups while still maintaining a lighter, more precise pedal!
SPECS
- CLUTCH KIT - These are available in 3 stages. See drop down boxes below for all options and their prices.
-JHM Stage 1 (Full Organic): Good for Stock, Stage 2+ and mild Stage 3 2.7t engines.
-JHM Stage 3 (hybrid Ceramic/Metal Backed Organic): Good for all Stage 3 K04 powered 2.7t engines
INCLUDES THE FOLLOWING -JHM Forged Chrome-Moly Lightweight Flywheel - New pilot bearing (already pressed in) - Flywheel to crank bolts - OEM B7 RS4 pressure plate - clutch disc (choose stage below before ordering) - Pressure plate to flywheel bolts - Throwout bearing - Clutch alignment tool.
INSTALLATION AND TORQUE NOTES HERE
NOTE: Clutch break-in is important and must be done properly. You need to do as much city type driving as you can for the first 500 miles the new clutch is in the car. Each time you start from a stop or shift it aids in the break in process. Highway mileage does not count. You also MUST avoid any racing activities, launching, or aggressive driving during the break-in period as this gets the clutch disc too hot. With that being said, you can go full throttle but you just can't speed shift or power shift.
NOTE: For those that are looking for a more robust, race oriented clutch setup we highly recommend looking into our R-Series line-up that does not have an SAC. The SAC in OEM and other aftermarket pressure plates work great for comfort and OEM-like drive-ability, however it is not designed to take excessive abuse of track days or aggressive street driving. We have done rigorous testing since 2012 to develop the ultimate clutch solution for both street and track and the R-Series is what is needed to take these cars to the next level.
For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.
- PDP tag:
- Free Shipping*
