JHM ECU Tuning or Tune for B6-A4 and C5-A6 3.0L V6

WARNING: This product can expose you to chemicals that are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.

Description
Fitment

Introducing JHM Tuning for the B6-A4 with the 3.0L V6!!!

*AS OF 7/23 B7 A4 TUNING HAS MOVED TO OUR POWER-CONNECT FLASHING SERVER AND REQUIRES THE POWER-CONNECT SOFTWARE*

IMPORTANT: After purchase you must email sales@jhmotorsports.com with your order number to receive your account credentials.

After a lengthy development period, we are excited to finally offer the JHM B6-A4 3.0L ECU Tuning. We went to great lengths to calibrate this tune to get the most out of your 3.0L V6 motor. Our tuning will completely change the performance of your car. You will experience increased and improved throttle response, increases in low end torque, and increases top end power. Our tuning also features our proprietary JHM Launch Assist feature! This is a great assist for those looking to launch their car easily and consistently, without any hassle. **NOTE: At this time, we only have a true Launch Assist for manual transmission cars. If you have an automatic/tiptronic car, consider purchasing our TCU tune which features an increased stall to help you get off the line faster.**

To see our tuning in action, feel free to check out the video below. Both of the B6-A4 3.0L cars featured in this video have the JHM ECU Tune along with several other JHM upgrades.

As we stated above, our JHM ECU Tuning you will give you noticeable improvements in the performance of your 3.0L. However, if you add our JHM 2.5" Stainless Steel Downpipes ON TOP of the ECU tuning, it will completely transform the power band of your car. If you are looking to unlock the potential of you 3.0L V6, these 2.5" downpipes are the key. Check them out in the Engine and Performance Section. They are an absolute MUST for anyone looking to get more power out of their car. Our extensive research proved this point time and time again. When we put our 2.5" downpipes on a stock car, the car was impressive and the increased airflow of the downpipes definitely made the car seem a bit more "peppy". However, when we put the downpipes on a car with a JHM B6-A4 3.0L V6 ECU Tune on it, the result was amazing. The combination of the increased airflow from the downpipes and the ability of the JHM ECU Tuning to take advantage of that increased airflow completely transformed the power band of the car. The gains in low-end torque were good but the most impressive power increase can be found in the top-end of the RPM range. With the motor breathing more freely and the addition of our ECU Tuning, the 3.0L just keeps accelerating up top!

OPTIONS: When you place your order for JHM Tuning, please specify your year, body type, octane, transmission type, and flashing method by using the drop down boxes below.

FLASHING INFORMATION:

For Flashing Method, select "Flash Myself, SEPARATE POWER CONNECT Cable Purchase Required, CLICK LINK BELOW" if you're going to be buying a cable from us and flashing your car on your own. You'll need to add this option.

GO HERE FOR JHM POWER CONNECT CABLE

and add to your cart after adding the tune, just selecting the option is NOT enough. Make sure you have THOROUGHLY read through the instructions and are confident that you can set your computer up correctly. If you select this option for your tune, you must select a shipping method for your order so we can ship you a JHM Tuning-Flashing Cable. Please select a shipping method once you've added the tuning and the flashing cable to your cart. Instructions for installing the flashing software on your computer will be emailed to you after purchase.

If you already have a JHM POWER CONNECT Cable, select "I already have a JHM POWER CONNECT Cable." **NOTE: This is a proprietary cable with drivers specific to our Flashing Software so you must make sure that you have a JHM POWER CONNECT Cable, NOT just a generic USB Vag Com cable.** After receiving your paid order, we will send you an authorization form which we will use to create your JHM Tuning Flash Browser account and login information. This is the information you will use to access our server and flash your car with the JHM Tuning-Flashing Cable that you already have.

DISCLAIMER: JHM is now using proven flashing technology in order to get our tunes on our customers' cars in the quickest and most convenient way possible. You will be installing a proprietary JHM software that works ONLY with our flash cable (supplemental software such as Microsoft .net may be required). This program is what allows you to detect your ECU part number, fill in your information, select the correct program based on your hardware and then write JHM Tune to your ECU all through your OBD II port. Both of these programs are highly specific when it comes to configuring your computer to run them properly. While every effort has been made to clearly and completely explain this configuration in our instructions, the customer will ultimately be responsible for removing or disabling their own or third party anti-virus software or firewalls that will block the port required for you to log into our flashing server (see the link to our instructions below to determine whether or not this is something you'll be able to do). Basic technical support provided by JHM to help install these programs on your computer, diagnose programs with your computer, and/or internet connection may be subject to an hourly fee. Additionally, if something happens to your ECU during the flashing process, you should be able to restore it using our software. If you are still unable to make the ECU flash properly, you will be responsible for all costs associated with restoring your ECU and fixing the issue.

Requirements for Tune:
- Windows computer with at least 1 USB (Universal Serial Bus) port
- Wired Broadband Internet Connection (wireless can be unreliable)
- JHM Tuning-Flashing Cable (Flash cable length cannot extend beyond 10 ft long unless a powered USB hub is installed in-line.
- Battery Charger or equivalent power source capable of sustaining a 40 amp charge

If you would like to get tuned at our location in Lathrop, CA please give us a call to schedule an appointment! If you'd like to get tuned at a JHM dealer close to your location, you can find one using our Dealer Map by clicking the "Dealers" Tab at the top of this page. You will need to contact your preferred dealer directly and schedule a tuning appointment with them. You shouldn't be charged more than an hours' worth of labor for your JHM Flash.

Our dealer network is large and growing daily. If we do not have a dealer within an hour drive of your location, we will do everything possible to build a new relationship with a shop close to you on your behalf. Please contact us for more information.

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout. If you are looking to purchase other products at the same time as your tune, please do so on a separate invoice.

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.

DO NOT SHIP YOUR ECU TO JHM without contacting us first!!!

NOTE for customers with an ECU that already has brand-x software:

**UPDATE, 10-1-2012:** JHM Flash Tuning technology will overwrite **most** previous tuning on your ECU. If you're already tuned with a poorly performing, "brand-x" ECU tune you do not need to worry about it interfering with the process for becoming JHM Tuned. However, if another company has installed a soldered on board like we used to, you will not be able to flash over that. In these cases, the customer will be responsible for all additional labor charges, shipping costs, etc. required to convert the ECU back to stock to allow it to be flashed.

Any previously tuned JHM ECU with a solder on board can be converted back to stock. This will allow the customer to convert to JHM Flash Technology. Previously tuned JHM ECU customers will need to send their ECU to JHM to have it converted to stock and then have the stock ECU installed in their car and tuned via JHM Flash Technology. If you go to a JHM Dealer to have your ECU removed, you will be responsible for all associated labor and shipping costs charged by the dealer. If you plan on flashing your car on your own, you will need to pay for a flashing cable as well.

When tuning ECUs from other platforms, we've ran into some issues with ECUs that are already chipped. We have found that other tuning companies sometimes make proprietary changes to your immobilizer chip (a chip for the anti-theft and other things separate from the main ECU chip), thus making the ECU unable to function with a stock chip or a JHM tune. It is an involved process for us to repair your ECU so it can again function with a stock or JHM chip. So please mention in the comments of your order if your ECU already has a tune on it. Please give us all the details about any programs you had installed so we can be prepared for any extra work involved with chipping your ECU. Keep in mind that any extra time we have to spend in tuning a previously chipped ECU will increase the turnaround time and potentially increase the cost of the tuning process itself.

For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout.