WARNING: This product can expose you to chemicals that are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.JH Motorsports is proud to release our JHM B8 Q5-SQ5 ECU and TCU Software!
Our Stage 1 and 2 performance ECU and TCU software is specifically designed to work in harmony together maximize the engine power output capabilities. With extensive research and testing with our in-house B8 Q5-SQ5 3.0T, we have created the ultimate software for your car. Our tuning will give your Q5-SQ5 3.0T improved throttle response, higher shift points, and more power throughout the entire RPM range leading to faster acceleration and a much more rewarding and refined driving dynamic.
This is a one-and-done solution with only ONE Flashing Cable Required (JHM Power-Connect) and can be flashed in the convenience of your own home with an internet connection.
By making an ECU and TCU combination that works together we were able to do the following for your B8 Q5-SQ5 3.0T:
- Engine Rev limit increased to 7400 rpm
- More aggressive throttle control
- Increased shifting speeds
- More assertive shifting in Sport mode and after launching
- Launch Stall RPM raised from ~2000 to ~3000 (outside factors can alter this result)
- More aggressive and consistent Launch
- Refined Drive and normal driving shifting dynamics
- Decreased Transmission wear due to less slipping from faster shifting
- Raised TQ limiters
- Maximum Boost for each Pulley Ratio
- Safe EGT Management for stock catalyst protection keeping your car as safe as possible while maximizing performance
- Free Upgrade from Stage 1 to Stage 2 to Stage 2+
Performance:
STOCK (BONE STOCK CAR) - We measured the car at 14.17@95.24mph - 2.08s 60ft - 57F - 91 Octane
JHM STAGE 1 (SOFTWARE ONLY ON STOCK VEHICLE) - We measured the car at 12.31@111.198mph - 93 Octane
JHM STAGE 2 (Single Pulley) w/ JHM 187mm Crank Pulley and JHM Silicone Inlet Hose - We measured the car at 11.96@113.28mph - 93 Octane
JHM STAGE 2+ (Dual Pulley) - COMING SOON
AVAILABLE FILES:
• Stage 1 - Stock Pullies
• Stage 2 - 179mm Crank Pulley or 57mm Supercharger Pulley (or other similarly sized pulley options)
• Stage 2+ DP - 207mm Crank Pulley, or Dual Pulley ( 57mm + 187mm combinations or similar)
• Stage 2+ DP w/80mm Throttle Body
Available Fuel Options:
• 91 Octane
• 93 Octane
• 100+ Octane (Race Gas)
• E40 Blend (91 + E85 or 93 + E85 mix)
Customer Supplied Dyno Graph: 402whp and 387wtq
FLASHING INFORMATION:
For Flashing Method, select "Flash Myself, SEPARATE POWER CONNECT Cable Purchase Required, CLICK LINK BELOW" if you're going to be buying a cable from us and flashing your car on your own. You'll need to add this option.
GO HERE FOR JHM POWER CONNECT CABLE
and add to your cart after adding the tune, just selecting the option is NOT enough. Make sure you have THOROUGHLY read through the instructions and are confident that you can set your computer up correctly. If you select this option for your tune, you must select a shipping method for your order so we can ship you a JHM Tuning-Flashing Cable. Please select a shipping method once you've added the tuning and the flashing cable to your cart. Instructions for installing the flashing software on your computer will be emailed to you after purchase.
If you already have a JHM POWER CONNECT Cable, select "I already have a JHM POWER CONNECT Cable." **NOTE: This is a proprietary cable with drivers specific to our Flashing Software so you must make sure that you have a JHM POWER CONNECT Cable, NOT just a generic USB Vag Com cable.** After receiving your paid order, we will send you an authorization form which we will use to create your JHM Tuning Flash Browser account and login information. This is the information you will use to access our server and flash your car with the JHM Tuning-Flashing Cable that you already have.
DISCLAIMER: JHM is now using proven flashing technology in order to get our tunes on our customers' cars in the quickest and most convenient way possible. You will be installing a proprietary JHM software that works ONLY with our flash cable (supplemental software such as Microsoft .net may be required). This program is what allows you to detect your ECU part number, fill in your information, select the correct program based on your hardware and then write JHM Tune to your ECU all through your OBD II port. Both of these programs are highly specific when it comes to configuring your computer to run them properly. While every effort has been made to clearly and completely explain this configuration in our instructions, the customer will ultimately be responsible for removing or disabling their own or third party anti-virus software or firewalls that will block the port required for you to log into our flashing server (see the link to our instructions below to determine whether or not this is something you'll be able to do). Basic technical support provided by JHM to help install these programs on your computer, diagnose programs with your computer, and/or internet connection may be subject to an hourly fee. Additionally, if something happens to your ECU during the flashing process, you should be able to restore it using our software. If you are still unable to make the ECU flash properly, you will be responsible for all costs associated with restoring your ECU and fixing the issue.
Requirements for Tune:
- Windows computer with at least 1 USB (Universal Serial Bus) port
- Wired Broadband Internet Connection (wireless can be unreliable)
- JHM Tuning-Flashing Cable (Flash cable length cannot extend beyond 10 ft long unless a powered USB hub is installed in-line.
- Battery Charger or equivalent power source capable of sustaining a 40 amp charge
You can download and view the instructions HERE to determine whether or not this is something you would like to do.
If you would like to get tuned at our location in Lathrop, CA please give us a call to schedule an appointment! If you'd like to get tuned at a JHM dealer close to your location, you can find one using our Dealer Map by clicking the "Dealers" Tab at the top of this page. You will need to contact your preferred dealer directly and schedule a tuning appointment with them. You shouldn't be charged more than an hours' worth of labor for your JHM Flash.
Our dealer network is large and growing daily. If we do not have a dealer within an hour drive of your location, we will do everything possible to build a new relationship with a shop close to you on your behalf. Please contact us for more information.
For shipping quotes: Please sign in or join then put the items you want in your shopping cart and proceed to checkout. If you are looking to purchase other products at the same time as your tune, please do so on a separate invoice.
