• APR 3.0 TFSI Supercharger Drive and Crank Pulley with Belt (Bolt on) - MS100185
  • APR 3.0 TFSI Supercharger Drive and Crank Pulley with Belt (Bolt on) - MS100185
  • APR 3.0 TFSI Supercharger Drive and Crank Pulley with Belt (Bolt on) - MS100185
  • APR 3.0 TFSI Supercharger Drive and Crank Pulley with Belt (Bolt on) - MS100185

APR 3.0 TFSI Supercharger Drive and Crank Pulley with Belt (Bolt on) - MS100185

Free Shipping*

MSRP: $570.00
(You save $57.05 )
$512.95
UPC:
00810009931430
Adding to cart… The item has been added
Order now and you should receive this item between Sunday and Tuesday

Verify fitment with your vehicle


WARNING: This product can expose you to chemicals that are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.

APR's Supercharger Drive and Crank Pulley Upgrades dramatically increase horsepower and torque by increasing the rotational speed of the factory supercharger. APR's Stage II Pulley ECU Upgrade makes the necessary engine management adjustments to handle the increased supercharger speeds, and in turn allows the engine to create more power. The pulleys are sold separately, allowing for multiple levels of performance, each of which builds upon the other. Finally, when combined with APR's Ultracharger Throttle Body Upgrade in a dual pulley setup, the system is alleviated of power robbing inlet restrictions, allowing the engine to achieve exciting new levels of performance!



APR Supercharger Drive Pulley Upgrade



APR's Supercharger Drive Pulley Upgrade decreases the diameter of the factory pulley from ~63"25mm to 57.75mm, which in turn spins the supercharger ~9.5% faster. This results in a healthy bump in horsepower and torque across the entire RPM range with the supercharger operating at a higher rate of speed. The pulley is CNC machined from billet stainless steel, e-coated black for an OEM appearance and is press fitted to the factory supercharger unit on Gen 1 models and bolted on on Gen 2 models with new OEM bolts.






APR Supercharger Crank Pulley Upgrade



APRs Supercharger Crank Pulley Upgrade increases the diameter of the factory pulley from ~162mm to ~187mm, which in turn spins the supercharger ~15.4% faster. This results in a larger bump in horsepower and torque across the entire RPM range, as the supercharger is spinning at an even higher rate of speed. The pulley retains the factory harmonically balanced crank pulley and bolts on top of the existing unit. It is CNC machined from light weight billet aluminum with weight saving pockets throughout. It has an anodized black finish and includes new crank pulley bolts.



Please note: For 3.0 TFSI Gen 2 engines (Simos 16), the Supercharger Crank Pulley is only available when used in a dual pulley configuration.



APR Supercharger Dual Pulley Upgrades



Upgrading both the supercharger drive and crank pulleys results in the factory supercharger spinning ~26.4% faster than stock. This speed was chosen after extensive engine and chassis dyno testing with various pulley sizes and supercharger speeds. The result is an even higher horsepower and torque gain across the entire RPM range. However, at the airflow levels achieved with a dual pulley setup, maximum power is severely restricted by the factory throttle body unit. The APR Ultracharger Throttle Body Upgrade is necessary to take full advantage of the dual pulley configuration, and is available in platform specific variations for the B8/B8.5 A4/A4/S4/S5, Q5/SQ5 and C7 A6/A7.



APR Stage II ECU Upgrade



APRs Stage II ECU Upgrade is designed for use with each pulley upgrade and only needs to be purchased once. The upgrade builds upon the APR Stage I ECU Upgrade, reconfiguring the engine management system to work in conjunction with the higher boost pressure and airflow levels achieved by spinning the supercharger faster. The Stage I ECU Upgrade is required to purchase the Stage II ECU Upgrade.






Supercharger Drive Pulley Removal Tool



The factory Gen 1 supercharger drive pulley is pressed on to the supercharger's input shaft. It's not possible to remove the factory pulley without damage, or damaging the supercharger itself unless special care and attention is taken.



The APR Supercharger Drive Pulley Installation Kit is designed to encapsulate the entire pulley and pull evenly across its entire surface. The unit is compact enough to not require complete removal of the front end of your vehicle, reducing labor time. Furthermore a provision was made to incorporate a 1/2 inch drive breaker bar which allows the entire assembly to be easily counter-held and ultimately makes the process a one man job.



A complete install manual covers the install process from start to finish, making installation easily completed at any APR dealer or in your own garage.



APR Stage II Calibration Report











































































































































































































































































































































































































Stage

Fuel
Max Power
HP
Max Torque
FTLBS
Max Power
Gain over Stock
Max Torque
Gain over Stock
- APR recommends and tuned with Sunoco GT 260 for 100 AKI mode and Sunoco GT 260 Plus for 104 AKI mode. Never use lower octane than specified by the mode.
- Max increases are based on APR's actual measured stock values and not those reported by Audi. | RON = ROW Fuel Grades | AKI = North American (RON+MON)/2 Fuel Grades.
- Reported wheel figures measured using APR's in house dynos using SAE J1349 correction and an average of multiple runs for all figures. Crank figures are estimated based on the measured wheel figures and APR's engine dyno results. Results will vary depending upon environmental conditions, vehicle, transmission, vehicle health, operating conditions, temperatures, fuel grade, dyno type, dyno setup, other variables and other modifications. For the best results, APR recommends removing the intake snow screen.
- Please note, transmission software is required to achieve power figures past the factory redline.
Audi S4/S5 (B8.5) (333HP)
Stage 2 Single Pulley 91 AKI / 95 RON 448 HP 381 FT-LBS +138 HP +101 FT-LBS
Stage 2 Single Pulley 93 AKI / 98 RON 458 HP 387 FT-LBS +148 HP +108 FT-LBS
Stage 2 Single Pulley 100 AKI / 104 RON 470 HP 398 FT-LBS +160 HP +117 FT-LBS
Stage 2 Single Pulley 104 AKI / 108 RON 481 HP 406 FT-LBS +171 HP +125 FT-LBS
Stage 2 Dual Pulley 91 AKI / 95 RON 445 HP 415 FT-LBS +134 HP +98 FT-LBS
Stage 2 Dual Pulley 93 AKI / 98 RON 468 HP 432 FT-LBS +157 HP +115 FT-LBS
Stage 2 Dual Pulley 100 AKI / 104 RON 513 HP 461 FT-LBS +202 HP +147 FT-LBS
Stage 2 Dual Pulley 104 AKI / 108 RON 527 HP 471 FT-LBS +215 HP +157 FT-LBS
Audi A4/A5/Q5 (272HP)
Stage 2 Single Pulley 91 AKI / 95 RON 448 HP 381 FT-LBS +166 HP +135 FT-LBS
Stage 2 Single Pulley 93 AKI / 98 RON 458 HP 387 FT-LBS +176 HP +142 FT-LBS
Stage 2 Single Pulley 100 AKI / 104 RON 470 HP 398 FT-LBS +186 HP +151 FT-LBS
Stage 2 Single Pulley 104 AKI / 108 RON 481 HP 406 FT-LBS +196 HP +159 FT-LBS
Stage 2 Dual Pulley 91 AKI / 95 RON 445 HP 415 FT-LBS +168 HP +135 FT-LBS
Stage 2 Dual Pulley 93 AKI / 98 RON 468 HP 432 FT-LBS +189 HP +152 FT-LBS
Stage 2 Dual Pulley 100 AKI / 104 RON 513 HP 461 FT-LBS +233 HP +188 FT-LBS
Stage 2 Dual Pulley 104 AKI / 108 RON 527 HP 471 FT-LBS +245 HP +198 FT-LBS
Audi SQ5 (354HP)
Stage 2 Single Pulley 91 AKI / 95 RON 448 HP 381 FT-LBS +71 HP +58 FT-LBS
Stage 2 Single Pulley 93 AKI / 98 RON 458 HP 387 FT-LBS +80 HP +65 FT-LBS
Stage 2 Single Pulley 100 AKI / 104 RON 470 HP 398 FT-LBS +91 HP +74 FT-LBS
Stage 2 Single Pulley 104 AKI / 108 RON 481 HP 406 FT-LBS +101 HP +82 FT-LBS
Stage 2 Dual Pulley 91 AKI / 95 RON 445 HP 415 FT-LBS +73 HP +87 FT-LBS
Stage 2 Dual Pulley 93 AKI / 98 RON 468 HP 432 FT-LBS +93 HP +104 FT-LBS
Stage 2 Dual Pulley 100 AKI / 104 RON 513 HP 461 FT-LBS +138 HP +130 FT-LBS
Stage 2 Dual Pulley 104 AKI / 108 RON 527 HP 471 FT-LBS +150 HP +140 FT-LBS
Audi A6/A7 (C7) (310HP)
Stage 2 Single Pulley 91 AKI / 95 RON 448 HP 381 FT-LBS +125 HP +101 FT-LBS
Stage 2 Single Pulley 93 AKI / 98 RON 458 HP 387 FT-LBS +134 HP +108 FT-LBS
Stage 2 Single Pulley 100 AKI / 104 RON 470 HP 398 FT-LBS +145 HP +117 FT-LBS
Stage 2 Single Pulley 104 AKI / 108 RON 481 HP 406 FT-LBS +155 HP +125 FT-LBS
Stage 2 Dual Pulley 91 AKI / 95 RON 445 HP 415 FT-LBS +126 HP +102 FT-LBS
Stage 2 Dual Pulley 93 AKI / 98 RON 468 HP 432 FT-LBS +147 HP +119 FT-LBS
Stage 2 Dual Pulley 100 AKI / 104 RON 513 HP 461 FT-LBS +191 HP +155 FT-LBS
Stage 2 Dual Pulley 104 AKI / 108 RON 527 HP 471 FT-LBS +204 HP +165 FT-LBS
Audi A6 (C6) (290HP)
Stage 2 Single Pulley 91 AKI / 95 RON 375 HP 373 FT-LBS +100 HP +79 FT-LBS
Stage 2 Single Pulley 93 AKI / 98 RON 388 HP 379 FT-LBS +114 HP +91 FT-LBS
Stage 2 Single Pulley 100 AKI / 104 RON 408 HP 389 FT-LBS +135 HP +107 FT-LBS
Audi A4/A5/A6/A7/A8/S4/S5 (333HP) Simos 16
APR Stage II Single Pulley 91 AKI / 95 RON 467 HP 398 FT-LBS +131 HP +106 FT-LBS
APR Stage II Single Pulley 93 AKI / 98 RON 477 HP 404 FT-LBS +140 HP +113 FT-LBS
APR Stage II Single Pulley 100 AKI / 104 RON 489 HP 415 FT-LBS +152 HP +122 FT-LBS
APR Stage II Single Pulley 104 AKI / 108 RON 500 HP 423 FT-LBS +161 HP +130 FT-LBS
APR Stage II Dual Pulley 91 AKI / 95 RON 435 HP 409 FT-LBS +112 HP +90 FT-LBS
APR Stage II Dual Pulley 93 AKI / 98 RON 458 HP 426 FT-LBS +133 HP +107 FT-LBS
APR Stage II Dual Pulley 100 AKI / 104 RON 503 HP 457 FT-LBS +177 HP +143 FT-LBS
APR Stage II Dual Pulley 104 AKI / 108 RON 517 HP 467 FT-LBS +189 HP +153 FT-LBS

PDP tag:
Free Shipping*

Reviews